Aluminum & Engineered Profiles
Vented aluminum soffit and fascia wrap in baked-enamel colors matched to your existing trim — coordinated with any roof, ridge-vent, or gutter work.
Vented · Color-Matched
Soffit and fascia installation and repair in New Jersey.
Aluminum and engineered soffit and fascia installed with venting that feeds the attic and protects the rafter tails. Proudly Serving Homeowners Throughout New Jersey.
Vented aluminum & engineered
Rafter-tail protection
NJ Lic 13VH13821400
THE SCOPE
Finishing the roofline the way it should be finished.
Soffit and fascia are the finish line of the roof — and the most common entry point for water and pests when they're neglected. Rotted fascia board is cut back to sound framing and replaced, then wrapped in baked-enamel aluminum or finished with engineered profiles, and vented soffit panels are sized to feed the attic so the ridge vent above has air to pull. Scoped alongside roof and gutter work, the whole roofline sequences and ages as one system.
Soffit and fascia are where water and pests get into a roof. We tear off rotted fascia board down to sound framing, replace it, then wrap in aluminum or install engineered profiles with vented soffit panels sized to the attic's intake needs — so the ridge vent above actually has air to pull. Done right, it closes the entry points and keeps the attic breathing. Proudly Serving Homeowners Throughout New Jersey.
WHAT’S INCLUDED
What a soffit & fascia project covers.
Fascia replacement
Rotted fascia board cut back to sound framing and replaced before wrap or gutters go up.
Vented soffit installation
Soffit panels sized to feed the attic's intake so ridge exhaust has air to pull.
Aluminum wrap & trim
Color-matched aluminum wrap on fascia, frieze, and corner trim for a finished, low-maintenance roofline.
Gutter & ventilation coordination
Soffit and fascia scoped alongside gutter and roof work so the whole roofline sequences correctly.
The eave as a system
Soffit and fascia are a system. We vent and seal both.
The soffit underneath and the fascia at the edge work together. Vented soffit feeds cool air into the attic; fascia caps the rafter tails and carries the gutter. Get one wrong and you trap heat, starve the ridge vents, or leave rafter tails exposed to rot.
01
Vented aluminum soffit
Perforated panel · ~9 sq in net free vent area per linear foot
The perforated underside is the intake half of a balanced attic system. It pulls cool outside air in at the eave so ridge vents can exhaust hot, moist air above the insulation.
02
Solid soffit
Sealed panel · used over porches & where intake is not required
A solid panel finishes the overhang cleanly where there is no attic to ventilate — porch ceilings, bump-outs, and runs already served by intake elsewhere. We never seal an eave that the attic depends on.
03
Engineered fascia
Capped board · carries the gutter & caps the rafter tails
Fascia caps the cut ends of the rafter tails and gives the gutter a straight, rot-resistant board to hang from. We wrap it in color-matched aluminum so water never reaches the wood behind it.
Venting feeds the attic and protects the rafter tails. Intake at the soffit plus exhaust at the ridge keeps the deck dry, the shingles cooler, and the wood behind your fascia from ever seeing standing water.
Vented aluminum & engineered · Rafter-tail protection · NJ Lic 13VH13821400
MATERIALS & MANUFACTURERS
Materials and manufacturers we install.
HOW WE WORK
Your Experience, Our Top Priority.
- 01
Initial Consultation & Inspection
On-site review of what's actually there — decking, ventilation, framing, flashings, or the rough opening, depending on the job. We photograph everything and walk you through what's wrong before we quote.
- 02
Project Planning & Launch
Itemized written scope, materials list, manufacturer warranty registration plan, and a start date. Permits pulled where the town requires them.
- 03
Swift and Seamless Execution
One accountable crew, one schedule. We protect the landscaping and interior, work clean, and button up the site at the end of each day.
- 04
Final Cleanup & Project Completion
Magnet sweep for nails, debris hauled, walkthrough with the project manager, and warranties registered the same day.
FINANCING
Spread the project across the years it'll last.
A new roof or full exterior shouldn’t come out of one paycheck. Financing options are reviewed during the estimate so the monthly number is clear before any work begins.
Pre-qualify in minutes
Soft credit check through Hearth — no impact on your credit score.
Plans that fit the project
Multiple lenders compete for your project so terms match the scope, not the other way around.
Transparent terms
Rate, term, and monthly payment laid out in writing before any work begins.
WHERE WE WORK
Proudly Serving Homeowners Throughout New Jersey.
Based in Wallington, NJ. Explore the county links below to find your community.
FREQUENTLY ASKED
Soffit & Fascia questions, answered.
RELATED SERVICES
Often paired with this project.
Ready to talk about your soffit & fascia project?
Free consultations. Honest estimates. Same-day call-back, every time.